![]() ![]()
OS CPE: cpe:/o:linux:linux_kernel:2.4 cpe:/o:linux:linux_kernel:3 #UPGRADE DD WRT V24 SP1 TO SP2 UPDATE#and use the firmware upgrade web interface to update your router with dd-wrt. Warning: OSScan results may be unreliable because we could not find at least 1 open and 1 closed port overclocking support in DD-WRT (verified in v24 SP1): /proc/cpuinfo output. Can anyone help to explain this output? Perhaps it's just an erroneous guess as the output suggests it may not be accurate? Thank nmap -O my public IP Was doing some basic nmap scanning from work against my home public IP, and the nmap scan is apparently saying I'm running DD-WRT? My only other router (wireless) is sitting behind the pfSense box and it is running stock firmware, not DD-WRT. It seems cool and powerful, but I haven't messed with it much yet. my current uptime is 195days 4hours+ and still going on build 12548.This weekend, I set up pfSense on a spare box that I had sitting in the garage. Your DD-WRT router is connected to your first router via wifi or ethernet. ![]() You have already hard reset or restore the factory defaults via the administration menu. Previous or other builds may have bugs preventing OpenVPN connections. actually i am on the build i described above but version 12548 as that was a recommended build not to long ago and is proven stable also. DD-WRT v24-sp2 (12/22/14) build have been used while preparing this tutorial. but according to some people it don't always work but for me and other routers i have it works well so if you want to play it extra safe just use the holding of the reset button for basically the 30-30-30 as it shows in the link) ) (i personally use the 'erase nvram' stuff as it's easier. ALWAYS do a 'hard-reset' before and after a firmware update (i.e. i am just assuming you got DD-WRT already up and running.īut remember one thing. (other need to know info talks about hard resetting router etc which is pretty much REQUIRED if you want to be sure that DD-WRT etc is running fine) but make sure to read all the proper precautions first) but since you got 4MB flash you most likely can use. dd-wrt.v24-15230_NEWD_mini_usb_ftp.bin, but you might need a different build depending on your options etc. (the firmware you should try first) (i use the Eko special builds myself. Use one of these firmwares if you want to have the most recent builds that have been tested to be stable. Seems in every post that I read you do the same thing again and again.Īnd as usual use the recommended firmware NOT the official release or what's recommended in the router database as it's outdated. One way to verify might be to use a different off the shelf router, if that works - then nothing in the custom firmware is required, and then you should be able to flash their provided hardware with something different, be it dd-wrt or just native dlink or some other 3rd party.ĭo you have to be such an ass when replying to someone? Not everyone has the knowledge. In these cases, hard resets and reconfiguration to the original settings fixed the problems. I would hope not, but you never know with some of the strange things these ISPs do to lock stuff down. began life running DD-WRT v23 SP2, has yet to ever be reset other than by a power outage.) Some, however, have not worked properly after the upgrade, and have caused reliability issues for the rest of the network to which they are attached. Flashing over to a generic firmware might prevent access to them. I would suggest you read the dd-wrt forums, or better yet post asking that specific question - hopefully someone from your same ISP has done it and can verify even after the flash you will have access with your isp, etc.Įdit: I doubt your isp made any changes to the actual hardware, but they could have done something specific in the firmware that permits access, etc. #UPGRADE DD WRT V24 SP1 TO SP2 SOFTWARE#So your ISP has their own software on this device? If so - are you sure if you flash it to dd-wrt that you will still have access? That is a good question!! "provided by my ISP which has its own custom firmware on" READ the hardware specific step by step instructions!!! "so i do the Initial Flashing first then the Webflash after from the web interface?" #UPGRADE DD WRT V24 SP1 TO SP2 INSTALL#Right in the instructions tells you exactly where to go and what to download.Īlso right on the wiki under install instructions.Ĭlearly points you to the hardware specific section - again where you devices is listedīe honest - your just to lazy to bother doing any reading at all. To install dd-wrt on a D-Link DIR-615 Revision C1/C2/E3/E4, you can flash it directly from the router's web admin page (yes, that is correct. Step-by-step instructions from out-of-the-box factory firmware Come on really? there is a link to the install instructions right off the supported devices page. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |